Dowel Pin Remover

Home > Pins / Dowel Pin Remover
Welcome to the Industrial and Scientific Tool!

The best site about Dowel Pin Remover

Cal-Van Tools 95400 In-Line Dowel Pin Puller Master Set
Price: $132.99
Buy Now >>
  • Can be used with air ratchet or traditional ratchet
  • Fits the appropriate sized collet over the dowel; tighten the sleeve; use outer sleeve and nut to extract the dowel
  • Master set includes both SAE and metric collets
100 Value-pack Disposable Dental Articulators Dowel-pin-free Model Frame with Hinge
List Price: $200.00 Price: $90.50 You Save: $109.50 (55%)
Buy Now >>
  • Close imitation of the Arc of Human Alveolar
  • Patented design offers exceptional die stability
  • Locking design allows occlusion height setting
Cal-Van Tools 95200 SAE Dowel Pin Puller
List Price: $150.66 Price: $113.00 You Save: $37.66 (25%)
Buy Now >>

Dowel Pin Remover - Recent Articles

Broken hub dowel pin removal? - IH8MUD Forum


  • Yeah, you should take it out. Those things are damn hard (hardened steel). You can try putting the hub in a drill press and drilling it (pin) out....start with a small bit and work up so you dont get into the hub itself. You'll need really good bits and be able to re-sharpen them. once you get the pin drilled down to a fairly thin wall, run a big screw into it and see if it will turn and you may be able to work it out. This may or may nor work, but its a place to start. That hub is the same on all toyotas, so it may be easier just to go get a new one from a junk yard. Take yours with just to be sure its the same. If you really want it out you can take it to a machine shop that does broken bolt and stud removals. The same process should work for the dowel. I doubt it will be cheaper than 80 bucks or so. If you try to do it yourself you will need a carbide drill bit or at the very lease, a cobalt one and the ability to resharpen it. You cold try welding a small bolt to it and pulling/twisting...
  • Read more...

    Source: Broken hub dowel pin removal? - IH8MUD Forum

    Dowel Pin Remover
    Best books
    Chilton's Auto Repair Manual, 1993-1997 Chilton's Auto Repair Manual, 1993-1997

    Creator: Chilton Book Company | Technology & Engineering - 1996-10-01 Remove the alignment dowel pin from the intake camshaft. Using a dowel pin remover tool, rotate the intake camshaft sprocket counterclockwise enough to slide the timing chain over the intake camshaft sprocket. Release the camshaft ... Publisher: Cengage Learning

    Direct and general support maintenance manual, tank, combat, full-tracked, 105-mm gun, M48A5, NSN (2350-00-582-5595) turret Direct and general support maintenance manual, tank, combat, full-tracked, 105-mm gun, M48A5, NSN (2350-00-582-5595) turret

    Creator: United States. Dept. of the Army | History - 1990 Inspection and Removal of Dowel Pins. a. Inspect dowel pins for wear and proper fit. Replace if defective. b. If necessary to remove dowel pins, use one of the following methods: (1) Grip pin with self-locking pliers and pull with a twisting ...

    Direct support and general support maintenance manual for tank, combat, full-tracked, 105-mm gun, M60A3 (2350-00-148-6548) and (2350-01-061-2306 TTS turret Direct support and general support maintenance manual for tank, combat, full-tracked, 105-mm gun, M60A3 (2350-00-148-6548) and (2350-01-061-2306 TTS turret

    Creator: United States. Dept. of the Army | Technology & Engineering - 1987 Inspection of Retaining Rings. Replace retaining rings if damaged. Do not attempt repair. 2-12. Inspection and Removal of Dowel Pins. a. Inspect dowel pins for wear and proper fit. Replace if defective. b. If necessary to remove dowel pins, use ...

    Direct support, general support, and depot maintenance manual for tank, combat, full-tracked, 105-mm gun, M60A1 W/E (2350-756-8497), tank combat, full-tracked ... vehicle, combat engineer, full-tracked, M728 W/E (2350-795-1797), gun elevating and turret traversing systems Direct support, general support, and depot maintenance manual for tank, combat, full-tracked, 105-mm gun, M60A1 W/E (2350-756-8497), tank combat, full-tracked ... vehicle, combat engineer, full-tracked, M728 W/E (2350-795-1797), gun elevating and turret traversing systems

    Creator: United States. Dept. of the Army | Technology & Engineering - 1990 Dowel Pin Removal. If necessary, remove dowel pins by one of the following methods: (1) Grip pin with self -locking pliers and pull with a twisting motion. (2) Grind pin off flush with surface and drill out remainder of pin with a drill of suitable  ...

    Organizational maintenance manual, tank, combat, full-tracked : 105-mm gun, M48A5 (2350-00-582-5595) turret Organizational maintenance manual, tank, combat, full-tracked : 105-mm gun, M48A5 (2350-00-582-5595) turret

    Creator: United States. Dept. of the Army | Technology & Engineering - 1978 Inspection of Retaining Rings. Replace retaining rings if worn, scored, or deformed. 2-23. Inspection and Removal of Dowel Pins. a. Inspect dowel pins for wear and proper fit. Replace if defective. b. If necessary to remove dowel pins, use one ...

    Dowel Pin Remover
    Jan 18, 2009 by xboxlover34 | Posted in Other - Games & Recreation

    I have large ones for holding my trigger/sear, a medium one for the hopper remover, and I have a tiny one. What is the tiny one for and where does it go?! first person to help me gets best answer.

    Oh thats cool, I've got the same exact gun (but with an AK-47 conversion kit). Yeah I use two big pins on the trigger, a medium one for the hopper remover, and the tiny one that you're talking about for the CO2 tank. Hope that helps.